martes, 24 de abril de 2012

La Fonera definitive cable

One of my old mobile phones (a Grundig) had a usb cable which has been around for a long time without much use, some time ago when plugging it into Linux I realised that it seemed like a standard usb to serial adaptor.

Bus 003 Device 002: ID 067b:2303 Prolific Technology, Inc. PL2303 Serial Port

[54027.595634] USB Serial support registered for pl2303
[54027.595855] pl2303 3-1:1.0: pl2303 converter detected
[54027.607264] usb 3-1: pl2303 converter now attached to ttyUSB0

So I analyzed it and found that it seemed like a 3.3V serial adaptor, so I had to start using it to access routers, mobiles, ... having also a broken Fonera power supply around (one of this typical Fonera problems where the power supply outputs the correct voltage but not enough intensity) I thought... if I put all this together I'll have a USB cable capable of powering La Fonera and also accessing it's serial port all in one and using just one USB slot.

And so... here is what I think is the definitive Fonera cable:

Recovering my fonera's filesystem files after f*cking it

Once upon a time I was cleaning up the jffs2 filesystem of my OpenWrt Backfire 10.03.1 based Fonera by removing "unused" packages and I thought... what is this hotplug2 package doing here, the fonera doesn't have anything hotplugable, so I can safely remove it... WRONG!

Never remove your hotplug2 package from your OpenWrt router, it won't complain, but once you reboot... at least on a Fonera with Backfire you are f*cked!

Hotplug2 is so needed that today, after finishing my definitive cable for La Fonera (I'll write about this later) when I saw it booting on the serial console, I watched my Fonera say on boot...

VFS: Mounted root (jffs2 filesystem) readonly on device 31:1.
Freeing unused kernel memory: 136k freed
Please be patient, while OpenWrt loads ...
Kernel panic - not syncing: Attempted to kill init!

and that was before getting to failsafe mode or anything, so... how could I gain access to the files I had inside if it was not booting?

It seems I went through the hard way, cause it resulted on a long way, that's why I'm writing it here...

I had access to the console and it has redboot on it (/me doesn't know anything about redboot), so I stopped redboot (I did this on the serial console but I have just realised that this can be done over telnet as well) and typed help, and then looking at my previous notes on how to flash OpenWrt I tried to enable capture on minicom (if you do this on telnet try to pipe it to tee) and dump the contents of the jffs2 filesystem using:

RedBoot> baudrate -b 115200
Baud rate will be changed to 115200 - update your settings
Baud rate changed to 115200 - continue (y/n)? y
Update RedBoot non-volatile configuration - continue (y/n)? n
RedBoot> fis list
Name FLASH addr Mem addr Length Entry point
RedBoot 0xA8000000 0xA8000000 0x00030000 0x00000000
rootfs 0xA8030000 0xA8030000 0x006D0000 0x00000000
vmlinux.bin.l7 0xA8700000 0x80041000 0x000E0000 0x80041000
FIS directory 0xA87E0000 0xA87E0000 0x0000F000 0x00000000
RedBoot config 0xA87EF000 0xA87EF000 0x00001000 0x00000000
RedBoot> fis load -b 0x80041000 rootfs
** Warning - checksum failure. stored: 0x136086ec, computed: 0x5571b53b
RedBoot> dump -b 0x80041000 -l 0x006D0000
80041000: 19 85 20 03 00 00 00 0C F0 60 DC 98 19 85 E0 01 |.. ......`......|
...

So, after some minutes I had all this hexa dump of the memory on my HD. Deavid kindly contributed this 90 secs python script to extract the hexa into binary (many thanks to him):

#! /usr/bin/python

from binascii import unhexlify
import sys

for line in sys.stdin:
colon = line.find(":")
end = line.find("|")
if colon < 0 or end <0:
sys.stderr.write(line)
else:
newline = line[colon+1:end].replace(" ","")
sys.stdout.write(unhexlify(newline))

And I had my jffs2 filesystem dumped on a file, yeah, so I thought I could simple mount -o loop it but... nope, jffs2 isn't that easy. Looking on the net I found that I should:

modprobe mtdram total_size=24576 erase_size=128
modprobe mtdblock
dd if=jffs2.img of=/dev/mtdblock0
mount -t jffs2 /dev/mtdblock0 /mnt

But that resulted on a mount: /dev/mtdblock0: can't read superblock error.

At that time I thought it could be an endianness problem, as I also wasn't able to mount an OpenWrt original jffs2 filesystem. So... a little more search on the net confirmed this and showed that:

apt-get install mtd-utils
jffs2dump -b -c -e dest_file.little src_file.big

should fix it, and so it did, after doing that and copying the new data converted from big endian to little endian to the mtdblock0 I was able to mount it and finally access all that I had on my Fonera.

That's it!

viernes, 6 de abril de 2012

Simyo sigue siendo el único con datos gratis.

Hace tiempo que no comento nada de telefonía, de hecho se me pasó comentar la mejora de una tarifa que para mi ya era buena para la gente que quiere datos, pero que ahora es todavía mejor. Estoy hablando de la tarifa del 5 de Simyo (5¢/min), una tarifa que te regalaba 300 megas de datos y desde hace un tiempo regala 555 megas, como recogió xatakamovil en su nota sobre la mejora de las tarifas de hablar y navegar de Simyo


La cosa por supuesto no viene por el morro, implica que hay un consumo mínimo de 6.99, pero es que si hablas algo por teléfono y le sumas cualquier tarifa de datos... vas a gastar más. Que yo sepa Simyo es la única que te da datos así por el morro al menos con un consumo tan pequeño, si alguien sabe de otra compañía que se le acerque que lo comente, pero por ahora, que yo sepa... es lo que hay.

En fin... ahora están con una buena promo de portabilidad, 15€ y 200 minutos, a lo que se pueden sumar de 5 a 10€ si te invita un amigo, como yo, así que si alguien quiere portarse, que aproveche y que ponga 0034692785565 en donde te dice lo de si tienes un codigo promocional, o sea, justo al empezar la solicitud, que te sale:



Son 10€ de regalo si os vais a contrato o 5€ si es a prepago, sólo por introducir el código y se puede usar para canjear por móviles o saldo gratis.